#K3s bandwidth setting for jt65 update
#K3s bandwidth setting for jt65 archive
#K3s bandwidth setting for jt65 windows

N1MM+ implements them with the help of either a hardware interface (TNC or TU) or more often, using вЂњdigital engineвЂќ software. These modes are conceptually quite similar to CW. There is no restriction on when a transmission may begin, other than the usual admonition to avoid having both parties to a QSO transmitting at once. These messages may be of arbitrary lengths and may contain any information that can be written down in letters and numbers. The first class of digital modes comprises вЂњconversationalвЂќ keyboard-to-keyboard modes in which the two parties to a QSO exchange messages made up of characters (letters, numbers or punctuation characters). There are two broad classes of digital modes supported by N1MM+.

Configuring a DXP-38 in one of the additional RX windowsДigital Modes WSJT (FT8,FT4) versus other digital modes (RTTY, PSK).

Additional Macros for the External TNC Interface.

The MMVARI Waterfall or Spectrum Window.

#K3s bandwidth setting for jt65 update

Why to Use вЂњAuto Update TRX Offset w/Mark Freq.вЂќ.When Should I Use the NET Option: NET On/Off with Run Change.The Digital Interface вЂ“ Menu Selections.

#K3s bandwidth setting for jt65 windows

Additional Receive-Only Windows for RTTY.Configuring the Entry Window Function Keys.Do You HaveвЂ¦ (what to check when it does not work).The Rate Improver вЂ“ Right Click = Return NOTВ Menu.WSJT (FT8,FT4) versus other digital modes (RTTY, PSK).Setup DX, DXpedition, and General Purpose Contests.Windows вЂ“ Table of Contents View (long).Call History and Reverse Call HistoryВ Lookup.

#K3s bandwidth setting for jt65 archive

Archive Files (1/2021) вЂ“ N1MM on WindowsXP.

RF GAIN at 3 OвЂ™Clock or less on noisy bandsДЇL1 to FL5 BW set to match labeled filter bandwidth exactly, not wider or narrower.Дў.8 kHz 8-pole filter on SSB (1. Faster can be bad.ДЄGC -S 20 - Factory default slow AGC decay rate (recovery time). Signals lower than THR behave as they would with AGC OFF ( +1 dB of RF = +1 dB of audio)ДЄGC -F 120 - Factory default fast AGC decay rate (recovery time). I may move this lower since pileups of loud guys can blend together, but I like this setting because it saves my ears.ДЄGC THR 010 - AGC kicks in at about S-8. Works with AGC-S only.ДЄGC PLS NOR - Loud static pulses do not pump AGC.ДЄGC SLP 010 - A pretty вЂњflatвЂќ AGC response curve. Reduces AGC-induced IMD, recommended for pileups. OK on Heil.ДЄF LIM 20 - Only takes affect when AGC is OFF (rarely used)ДЄGC DCY Soft - Reduces AGC-induced IMD, recommended for pileupsДЄGC HLD 0.05 - Slow AGC hold time (50 ms). Set TECH MD OFF when finished, to eliminate useless options from appearing in the SubRx display choices (PLL1, AFV, dBV, etc.)ДЄF GAIN LO - Cuts audio hiss. N1EU recommended settings for best pileup performance:ДЄGC SLP 000 (maximum slope, instead of horizontal)ДЄGC THR 014 (so AGC doesnвЂ™t kick in until signals are very strong)ДЄF Gain is adjusted so the loudest signals are tolerably loud (around 9PM) and RF Gain increased until weakest signals are readable (around 3PM).Д«ob, N6TV, recommends the following K3 settings:ДЇirst set CONFIG:TECH MD ON to un-hide some AGC settings. I am creating this page to record all of the various settings in the radios so I can find them if needed. I have two Elecraft K3 radios that I use for SO2R.